Scope of application of grain conveyor and reasons for damage to the rubber surface covered by the conveyor belt

The reason why the grain conveyor replaced the previous loading and unloading workers is that machines can improve the speed of transporting grain. Of course, the time savings are still significant. We all know that some grain stores are specifically used to purchase grain, so they hope to collect more grain. However, if the conveying efficiency of the conveyor is low, it will delay their collection speed. Therefore, in the same time, if two bags of grain could have been transported, it was because the speed of human labor was relatively slow, so only one bag of grain could be purchased. Therefore, if the speed is slow by half, the amount of grain purchased will be reduced by half. Therefore, the staff of grain stores naturally hope to improve the transportation speed of grain. The speed, This is the only way to purchase a certain amount of grain faster and transport it to the places in need more quickly. The main component of the grain conveyor machine is a very long large belt, which can run from the beginning to the extreme end of the machine. The length of the belt is more than twice the length of the machine. Therefore, when we look at this machine, the first thing we see is this type of conveyor belt. In fact, such belts are prone to wear and tear, so it is often necessary for grain store staff to conduct regular inspections of the belt to see if any parts have signs of damage. If there are signs of belt breakage in some parts, it is necessary to replace the severely worn belt in a timely manner, because if the belt breaks by itself, it may delay the work of transporting grain. Therefore, it is still necessary to take protective measures in advance. So that when the belt breaks, The staff don't know where to start repairing or are busy with choosing belts.

Scope of application of grain conveyor: Mobile belt lifting belt conveyor for loading and unloading grain conveyor is not limited to the use site. The belt conveyor has wheels under it, which can move back and forth. Grain conveyor has the advantages of simple structure, economy, convenience, reliable use, smooth transmission, large conveying capacity, high efficiency, low noise, etc. It has various forms and a wide range of applications, especially suitable for conveying scattered raw materials and irregular items. It is a relatively convenient and fast belt conveyor for loading and unloading. When the capacity and distance of the grain conveyor are large, an intermediate drive device can be equipped to meet the requirements. According to the requirements of the conveying process, materials can be conveyed by a single machine or by combining multiple units into a horizontal or inclined transportation system. The solution to the problem of the tail wheel of the grain conveyor: The tail wheel of the grain conveyor is generally prone to problems, and if there is a problem with the tail wheel, it will affect the normal operation of the grain conveyor. It is more likely to cause the material belt to deviate, and then the material cannot be transported to the designated height and location during the conveying process. If there is a problem with the tail wheel of the grain conveyor, the corresponding head wheel will also inevitably have problems, because the tail wheel and head wheel are in a vertical meeting. If the transmission shaft is in a vertical plane but unbalanced, it will cause the transmission shaft of the head wheel and tail wheel to deviate. Although the two transmission shafts are parallel, they are in the same vertical plane but not horizontal, which will cause the hopper to deviate. The deviation of the grain conveyor hopper may collide with the machine barrel, and the hopper belt will tear along with it. We all know that the front end of the grain conveyor will bear a relatively large dynamic pressure, and long-term operation of the bearings will definitely cause squeezing wear. Some people use simple welding or brushing plating to save trouble and continue to use, but this will definitely have drawbacks. It is easy to cause material damage to the welding part, and if used again, it will bend or break, which will still cause the problem of head and tail wheel offset, and cannot fundamentally solve the problem. Reason for damage to the rubber surface of the grain conveyor belt cover: 1. Inappropriate gap between the guide groove lining plate and the tape, resulting in abnormal wear, or foreign objects embedded in the gap, causing abnormal wear or scratches. 2. The material flow rate at the guide chute is not consistent with the speed of the grain conveyor belt, resulting in a large drop and accelerating the wear of the rubber surface. 3. The roller is damaged, causing abnormal wear or scratches on the tape. 4. Violation of work regulations, burns caused by welding slag during maintenance, and scratches on cleaning equipment. 5. Slippery tape can also cause abnormal wear of the tape.